FlowRunner
Features Pricing
Theme
Start Free

Accessorial Charges: Check Detention, Lumper, and TONU Before You Pay

Accessorial charges are a carrier's extra fees for time or work on a load. How to check detention, lumper, TONU, and layover against evidence before you pay.

Plum card headed Accessorial charges with the statement Pay the wait you can prove., the line Stop times and receipts are checked first., and a tally of 3 charges, 2 proven, and 1 question.

Accessorial charges are the fees a carrier bills on top of linehaul and fuel for extra time or work on a load. On truckload invoices the common ones are detention, lumper, TONU, and layover. Each one is a claim that something happened on the load, so you pay it when the evidence on the load backs it up.

Finding that evidence is the slow part. Someone opens the TMS for stop times and digs the lumper receipt out of an email, then waits on the rep to say whether a TONU was real. A FlowRunner flow does the lookups on every invoice, clears the charges the evidence proves, and asks the rep only about the ones it can’t.

  1. 1Invoice arrivesA PDF in your carrier invoice inbox
  2. 2Agent reads itEach extra charge, the receipts, the rate con terms
  3. 3Evidence checkedStop times and documents on the load
  4. 4The rep decidesOnly the charges with no proof
  5. 5Bill createdWith the evidence for each charge

One invoice with three accessorials, start to finish

Here is a sample invoice from Bluebonnet Freight Lines for a reefer load from Salinas, CA to a grocery warehouse in Phoenix, AZ. The flow read the PDF and the lumper receipt attached to the email. It found the load in Turvo, pulled the stop times, and read the rate confirmation on the load for its accessorial terms. Detention starts after 2 hours, counted from the later of arrival or appointment, at $70 an hour. Lumpers are paid at cost with a receipt.

Bluebonnet Freight LinesInvoice 7731, Nov 10, 2026, load 51904-22816
ChargeEvidence the flow foundInvoice
Linehaul and fuelRate con: $3,100.00 and $520.00$3,620.00
Detention, 2.5 hours at $70Turvo, Nov 6: appointment 6:00 AM, arrived 5:52 AM, departed 10:30 AM$175.00
4 hours 30 minutes from the appointment to departure, less 2 hours free, is 2.5 hours at $70. Matches the hours billed.
LumperReceipt R-40917 attached to the email, $245.00$245.00
The receipt is dated Nov 6 at the Phoenix delivery and shows the load number and the same amount.
TONU, Nov 4No cancellation on the load$200.00
The load has one pickup, on Nov 5, and the truck loaded on time. Nothing on the load says a truck was turned away on Nov 4.
Total$4,240.00

Detention and the lumper clear on their own. The TONU has nothing behind it in the system, so the flow holds that line and asks Ana, the rep who covered the load, in Slack:

Slack, direct message to the rep on the load

F
FlowRunner9:31 AM

TONU with no cancellation: Bluebonnet Freight Lines, load 51904-22816

Invoice 7731 bills a $200.00 TONU for Nov 4. The load shows one pickup, Nov 5. Detention ($175.00) and the lumper ($245.00) are proven and ready to pay.

Approve $200DisputeAsk for proof
AB
Ana Brooks9:38 AM

What does the carrier say happened on Nov 4?

F
FlowRunner9:38 AM

Their email says the driver reached the shipper at 7:10 AM on Nov 4 and was sent away because the load wasn't ready. The rate confirmation sets pickup for Nov 5 at 7:00 AM, and Turvo shows the truck arrived 6:48 AM that day.

Ana knows the pickup was always booked for Nov 5 and the carrier sent a truck a day early, so Ana clicks Dispute. The flow replies in the carrier’s email thread with the booked pickup date, and creates the bill in QuickBooks Online for the rest:

Note on the billBill 7731 for Bluebonnet Freight Lines, $4,040.00, invoice and receipt attached, QuickBooks Online

Invoice 7731, load 51904-22816. Linehaul $3,100.00 and fuel $520.00 match the rate confirmation. Detention $175.00 cleared from Turvo stop times: appointment 6:00 AM, out 10:30 AM, 2 hours free, $70 an hour. Lumper $245.00 cleared against receipt R-40917. TONU $200.00 disputed by Ana Brooks in Slack, Nov 11, 9:42 AM: pickup was booked for Nov 5.

The flow also attaches the invoice and the lumper receipt to the load in Turvo and adds the approved detention and lumper to the customer’s charges, so the shipper is billed for both. Then it marks the load Ready for billing.

An invoice whose accessorials all check out becomes a bill without anyone opening it. Every run keeps a step-by-step record of what the flow checked and who decided.

Invoices come in through Gmail, and the stop times and documents come from Turvo. The rep answers in Slack, and bills go to QuickBooks Online.

Common accessorial charges and the evidence behind them

The terms in the last column are typical examples, not market rates. Your rate confirmations set yours. On free time, Truckstop’s accessorial guide says most carrier agreements give two free hours at each facility before detention starts.

ChargeWhat it isEvidence that proves itTypical rate con term (example)
DetentionThe driver waits past free time at pickup or deliveryArrival and departure times against the appointment, from the TMS or stamped on the BOL or POD2 hours free, then $50 to $75 an hour, from the later of arrival or appointment
LayoverThe truck is held overnight and delivers the next dayStop times showing the truck was held into the next dayA flat amount per day, such as $250
LumperA third-party crew unloads the trailer for a feeThe lumper receipt with the facility, date, load or PO number, and amountReimbursed at cost with a receipt
TONUTruck ordered, not used: the truck was dispatched and the load canceled or not readyA cancellation on the load, or the rep’s confirmationA flat amount if canceled after dispatch, such as $150 to $250
Driver assistThe driver loads or unloads the freightA note on the BOL or POD signed by the facilityA flat amount, agreed before pickup

How to check an accessorial before you pay it

  1. Read what the charge claims happened, where, and when.
  2. Find the term on the rate confirmation. A charge with no agreed term goes to the rep.
  3. Pull the evidence: stop times, the receipt, or the load’s status.
  4. Do the math with the rate con’s terms. For detention that means free time, when the clock starts, the hourly rate, and any cap.
  5. Clear what the evidence proves, and send the rest to the rep on the load.
  6. Tell billing which charges you approved, so the shipper is billed for them under the customer contract.
  7. Keep the evidence with the bill.

Step 6 matters because a broker sits in the middle of every accessorial. Detention you pay the carrier and never bill to the shipper comes straight out of your margin on the load. For the base audit of linehaul, fuel, the POD, and duplicates, see freight invoice audit.

Exceptions and what the flow does

ExceptionWhat it looks likeWhat the flow does
Late driver billing detentionArrived 50 minutes after the appointment, billed 2 hours of detentionChecks your rate con’s rule for late arrivals and asks the rep, with both times
No stop times in the TMSThe driver never checked in or out in the appReads the in and out times stamped on the POD, or asks the carrier for them
Lumper with no receiptA $245 lumper line and nothing attachedLooks for the receipt on the load in Turvo, and if none is there, asks the carrier for it in their email thread and holds that line
Layover with a same-day deliveryLayover billed, but the truck left the receiver that afternoonAsks the rep, with the departure time
Billed twiceDetention on the invoice and again on a separate invoice a week laterFinds the earlier bill and stops the second charge

Brokers and 3PLs can see the rest of what a flow handles on the logistics page.

How to start

Start with detention and lumpers. Their evidence is already on the load or attached to the invoice, so the flow can clear them without asking anyone.

For the first two weeks, send every TONU and every charge without a rate con term to the rep. Then set the amounts you approve without a question, carrier by carrier, from what your reps approved.

Frequently asked questions

What are accessorial charges in trucking?

Accessorial charges are fees a carrier bills on top of linehaul and fuel for extra time or work on a load. Detention, lumper, TONU, and layover are the ones a truckload broker sees most. Each one should be agreed on the rate confirmation and backed by evidence before it is paid.

What is a TONU charge?

TONU stands for truck ordered, not used. The carrier bills it when a truck is dispatched for a load that is then canceled or not ready, and the rate confirmation sets the amount and the cutoff after which it applies. Before paying it, confirm the load was actually canceled or refused after that cutoff.

Who pays the lumper fee?

The driver pays the unloading crew at the dock, and the carrier bills that amount back on its invoice with the lumper receipt. In brokered truckload the broker reimburses the carrier at cost under the rate confirmation and bills the shipper under the customer contract. No receipt, no reimbursement.

Editorial policy

See how this would work on your stack

A 30-minute walkthrough against your actual setup, or have our team custom-build it for you.